| Click Here for Printer Friendly Version |
cleaning critical surfaces
UltraSOLV®
|
||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Description |
UltraSOLV® is a highly absorbent, Class 10 Wiper constructed from a naturally reticulated, hydrophilic, polyurethane foam. Using Foamtec's patented cleaning process and foam technology, UltraSOLV® Wipers are ideal for cleaning critical tools and assemblies. Available as a sponge for use with UltraSOLV® ScrubPADs on wet cleans.
| Advantages |
 |
The unique abrasion resistance and conformable characteristics of UltraSOLV® allow it to clean rough, coarse and bead blasted surfaces that will snag traditional polyester wipers. |
|
Low levels of particle generation, ionics, organics, lot-to-lot consistency and fiber free construction combined with unsurpassed contamination removal properties make it the ideal tool for the cleaning of critical process equipment. |
|
Sponge-like absorbency and rinsing characteristics offer the opportunity to significantly reduce wiper usage and hazardous waste generation in equipment PM's. |
|
Excellent static dissipative and tribocharging properties allow for safe cleaning of static sensitive assemblies, such as wafer transfer chambers in vacuum tools. |
| Applications |
Performing wet cleans and PMs on vacuum based process equipment in the Semiconductor, Disk Drive and Flat Panel Display industries.
| Part Numbers |
| Part No. | Product Description | Measurements | Bag Qty. | Case Qty. |
| HT4734 | Sponge | .37" x 2.62" x 4.37" | 1/bag | 100 bags/case |
| HT4752 | Sponge | .19" x 5" x 5" | 10/bag | 10 bags/case |
| HT4754 | Sponge | .375" x 3.625" x 5.375" | 1/bag | 100 bags/case |
| HT4790 | Wiper | .0625" x 9" x 9" | 50/bag | 30 bags/case |
| HT4790-5 | Wiper | .0625" x 9" x 9" | 5/bag | 200 bags/case |
| HT4794 | Wiper | .055" x 9" x 9" | 75/bag | 30 bags/case |
| HT4794-25 | Wiper | .055" x 9" x 9" | 25/bag | 50 bags/case |
| Cleanliness |
 |
| UltraSOLV® Wiper Out-of-the-Bag |
 |
| Standard Polyester Wiper Out-of-the-Bag |
 |
UltraSOLV® Wiper After Use on Bead Blasted Tool Surface |
 |
| Standard Polyester Wiper After Use on Bead Blasted Tool Surface |
| Particles > .5µ / m2 | Particles/Fibers > 25µ / m2 | |
| HT4790 | < 3,600,000 / m2 | 0 |
| HT4754 | < 20,600,000 / m2 | 0 |
| TVNRs | ||
| DI H20 < 1 ug/gram | IPA <.07 g/m2 | Methanol <.05 g/m2 |
| Ions in DI H2O | |||||
| Chloride | < 6 ppm | Sulfate | < 1 ppm | Silicon | < 1 ppm |
| Calcium | < 4 ppm | Sulfite | < 1 ppm | Magnesium | < 1 ppm |
| Sodium | < 4 ppm | Potassium | < 2 ppm | Nitrate | < 2 ppm |
All product is lot tested; lot certificates available upon request. |
|||||
| ESD Performance |
| Surface Resistance | 1.7 x 109 | ||
| Volume Resistance | 1.1 x 1010 | ||
| Electrostatic Delay | ± 5 kv to ± 10 volts | < 1.5 seconds | |
| Tribocharge | Less than 8 volts when wiped dry across stainless, aluminum, polypropylene and polyamide surface materials |
||
All measurements performed at 50% RH |
|||
| Methods of Use |
To maximize usage of Wiper: |
|
| a) Use with IPA Solvent: Apply a thin stripe of IPA, using a needle-nosed squeeze bottle, to the area just behind the rounded fold. Do not over wet Wiper. |
|
| b) Use with DI Water: Fully saturate by applying a quarter-sized amount of DI Water to the center of an unfolded Wiper, wring to ensure proper absorption, repeat until completely wetted. |
|
 |
 |
|
Step 1: Quarter-fold Wiper after wetting with DI Water. For use with IPA, quarter-fold prior to wetting. |
Step 2: With all four fingers on top and the thumb on the underside of the Wiper, pull it across the surface of the tool using very light pressure. |
